Problem in 10892 H

[zoran89]

Re: Problem in 10892 H

Sorry, I can't understand

I have something like this and I cant watch TV and use this at same time in the same room, so you could try to shutdown things one by one until you find what is make interference.

Or you dont have right paremeters, try to enroll this manuel, 10892 H 27500 3/4


Reciver cant have problem with only one freqency,
you sad that you having problem with only this transponder and it is not only one on this beam,
LNB must work on 10892 if it work on 10900.

So it must be some interference with other devices in your house.

[anacondama]

Re: Problem in 10892 H

I have a motor, and I tried to move east and west, with no success.
But it is the same satellite, other tp's have high signal, only this very weak.

is not the same east/west and up/down ... try this one it may work ... try to upgrade your box or just make the factory setup ( remove all your configuration )

Good Luck !

[peremacedonia]

Re: Problem in 10892 H

i try to find this frequency but it is only 63% no signal ....

[Jerry2020]

Re: Problem in 10892 H

I have something like this and I cant watch TV and use this at same time in the same room, so you could try to shutdown things one by one until you find what is make interference.

Or you dont have right paremeters, try to enroll this manuel, 10892 H 27500 3/4


Reciver cant have problem with only one freqency,
you sad that you having problem with only this transponder and it is not only one on this beam,
LNB must work on 10892 if it work on 10900.

So it must be some interference with other devices in your house.

I went over the roof, attached the box to the dish, and I had the same problem.

[Jerry2020]

Re: Problem in 10892 H

is not the same east/west and up/down ... try this one it may work ... try to upgrade your box or just make the factory setup ( remove all your configuration )

Good Luck !

I tried two other boxes and had the same problem. I don't think it is the box.

[Jerry2020]

Re: Problem in 10892 H

i try to find this frequency but it is only 63% no signal ....

Is it 63% for all nilesat, or just this tp?
For me, nilesat is has high signal, only this too low.

[lulezim]

Re: Problem in 10892 H

Hello all
I have a problem with the transponder 10892 H 27500 on Nilesat and on most other satellites.
On nilesat, I can receive all channels except this one. On other satellites, this transponder or close ones are very weak. Though I don't have problems with other transponders, and the dish is 180cm.
I can't figure out the reason.
Any help would be appreciated.

and I this problem I've had
I moving LNB left-right.
If there is a triangle sign

Otherwise apostatize a new head

[zoran89]

Re: Problem in 10892 H

Try add new transponder list, maybe FEC isnt correct to you.

[Jerry2020]

Re: Problem in 10892 H

and I this problem I've had
I tune moving head-left-right.
If there is a triangle sign (Then the center must)

Otherwise apostatize a new head

Sorry, I can't understand.

Try add new transponder list, maybe FEC isnt correct to you.

I tried all FEC values, even auto, with no success.

[lulezim]

Re: Problem in 10892 H



move in the center LNB

[zoran89]

Re: Problem in 10892 H

It cant be in Dish alingment problem, he sad that he have strong signal on other transponders, and I think he say that this is on motor and motor automaticly skew LNB.

[skytec]

Re: Problem in 10892 H

High-voltage lines, radar, local transmitters could cause interference ...

[Jerry2020]

Re: Problem in 10892 H

High-voltage lines, radar, local transmitters could cause interference ...

There are no high voltage lines nearby.
But other people who live near me have no such problem. Could this interference be concentrated on a small area?
Is there a solution if it is interference?

[satman72]

Re: Problem in 10892 H

Yes one can be to mount the dish updown side, but so you can't use it on motor. I mean you can mount the dish updown side on pole, so the dish will be pointed much high in elevation so to avoid terrestrial interferences. Look this pic to know better what I mean.

http://img167.imageshack.us/img167/5798/pict1628cf9.jpg

http://img524.imageshack.us/i/dcp2752ms3.jpg/

If you'll mount the dish so the elevation will be high and you'll need to calculate it by yourself but like you see expecially into second pic, the dish will be avoid all terrestrial interferences because it will point straight to sky.

[skytec]

Re: Problem in 10892 H

There are no high voltage lines nearby.
But other people who live near me have no such problem. Could this interference be concentrated on a small area?
Is there a solution if it is interference?

I don´t know.
Or try to move the dish to another location ??