Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

mgcamd problem on skybox f5

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • shadowmalik
    Member
    • Apr 2013
    • 33

    mgcamd problem on skybox f5

    I created an mgcamd.list file from my N line and tried to load this to my skybox f5 with a usb but the sky box wont recognise it as a valid mgcamd.list.

    I then tried entering the N line manually in the mgcamd setup option with the remote and everything works fine.

    I made sure I did all the basics like use notepad ++ and saving the file as *all files but always the same result no valid mgcamd.list file found.

    Anyone had the same problem??
  • kalpikos
    Experienced Board Member
    • Sep 2011
    • 7663

    #2
    Re: mgcamd problem on skybox f5

    Hi shadowmalik

    Are you sure that the spelling of the N-line is ok?

    A N-line inside your newcamd.list should be looks like:

    CWS = server.com 20000 user123 845795 01 02 03 04 05 06 07 08 09 10 11 12 13 14
    Try again and check the spelling
    If You Like My Post..... Please Press the Thanks Button

    Comment

    • shadowmalik
      Member
      • Apr 2013
      • 33

      #3
      Re: mgcamd problem on skybox f5

      cheers

      No its just

      N:server port user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14

      Comment

      • sataday
        Board Senior Member
        • Dec 2011
        • 327

        #4
        Re: mgcamd problem on skybox f5

        Originally posted by shadowmalik
        cheers

        No its just

        N:server port user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14
        Then, as kalpikos says, change the N: to CWS =

        Comment

        • kalpikos
          Experienced Board Member
          • Sep 2011
          • 7663

          #5
          Re: mgcamd problem on skybox f5

          Originally posted by shadowmalik
          cheers

          No its just

          N:server port user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14
          Hi

          Try to change the line in order to be in this form:

          Code:
          CWS = server port user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14
          As sataday said, just replace the "N:" with "CWS = "

          pay attention in syntax, there is a space before and after =

          Good luck
          If You Like My Post..... Please Press the Thanks Button

          Comment

          • aplok
            Experienced Board Member
            • Jun 2013
            • 1155

            #6
            Re: mgcamd problem on skybox f5

            ... hello ...

            have you allow your protocol with G: setting in mg_cfg ?

            Code:
            # network mode, use summ for several clients
            #    00 no network (default)
            #    01 newcamd netclient
            #    02 radegast netclient
            #    04 camd3 netclient
            #    08 gbox netclient
            #    32 cccamd netclient, card list saved as /tmp/cccamd.info
            #       (ECM only, supported server version up to 2.1.1, later not work)
            G: { 01 }
            so for cccam + newcamd : 1 + 32 : 33
            Code:
            G: {33}

            Comment

            • kalpikos
              Experienced Board Member
              • Sep 2011
              • 7663

              #7
              Re: mgcamd problem on skybox f5

              Originally posted by aplok
              ... hello ...

              have you allow your protocol with G: setting in mg_cfg ?

              Code:
              # network mode, use summ for several clients
              #    00 no network (default)
              #    01 newcamd netclient
              #    02 radegast netclient
              #    04 camd3 netclient
              #    08 gbox netclient
              #    32 cccamd netclient, card list saved as /tmp/cccamd.info
              #       (ECM only, supported server version up to 2.1.1, later not work)
              G: { 01 }
              so for cccam + newcamd : 1 + 32 : 33
              Code:
              G: {33}
              Hi aplok

              If I'm not mistaken, the skybox f5 it's not a linux box and therefore there is no "mg_cfg".

              It can handle both cccam and mgcamd but there is no way for advanced configuration.
              If You Like My Post..... Please Press the Thanks Button

              Comment

              • shadowmalik
                Member
                • Apr 2013
                • 33

                #8
                Re: mgcamd problem on skybox f5

                cheers

                Exactly right, the F5 is plug and play.
                so there is no way to edit mg_cfg

                Comment

                • aplok
                  Experienced Board Member
                  • Jun 2013
                  • 1155

                  #9
                  Re: mgcamd problem on skybox f5

                  Originally posted by shadowmalik
                  cheers

                  Exactly right, the F5 is plug and play.
                  so there is no way to edit mg_cfg
                  welcome in jail

                  their better world they knowingly design for us

                  Comment

                  Working...