Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

Can not get SkyGrabber with SkyStar S2 to work

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SatWaveDude
    Board Senior Member
    • Apr 2012
    • 220

    Can not get SkyGrabber with SkyStar S2 to work

    I've been trying to get SkyGrabber to work with SkyStar S2 PCI card but with no luck

    First I could get no signal from my LNB via a diseqc switch.
    But I found the the problem that was in conflict with SkyGrabber.
    It was caused a conflict by a software from TechniSat:

    Name: Server4PC
    The file is: Server4PC.exe

    This software is automatic started when you boot your system.

    When you close this (Server4PC) file SkyGrabber wil see signal.

    Are there any additional drivers that I have to install to get it to work?
    SatWaveDude

    DM500HD, DM500+ | EMP S16/1PCP-W3 | WaveFrontier T90 | 16x SMART Titanium 0.1dB LNB's
    TechniSat SkyStar S2 PCI / SkyStar USB HD
    WaveFrontier T90 rev.2 - 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 3.3E | 4/5E | 0.8W | 7/8W | 12.5W

    If you find my post usefull please press the Thanks Button
  • ftaboy
    Banned
    • Nov 2010
    • 402

    #2
    Re: Can not get SkyGrabber with SkyStar S2 to work

    Originally posted by SatWaveDude
    I've been trying to get SkyGrabber to work with SkyStar S2 PCI card but with no luck

    First I could get no signal from my LNB via a diseqc switch.
    But I found the the problem that was in conflict with SkyGrabber.
    It was caused a conflict by a software from TechniSat:

    Name: Server4PC
    The file is: Server4PC.exe

    This software is automatic started when you boot your system.

    When you close this (Server4PC) file SkyGrabber wil see signal.

    Are there any additional drivers that I have to install to get it to work?
    yes the problem of conflict signal is with TechniSat software, the Server4PC trying to lock on other frequency and the Skygrabber try to lock another frequency at the same time , when you close Sever4PC its ok, so , btw , you can go to : Run > msconfig > startup , to disable Server4PC to not run on windows startup....
    you dont need any other additional driver the driver is installed is okay. but i recommend you use SkyNet for sat fishing because it use lower resource than SkyGrabber , presonally i was had a lot of problem with it, sky net is the best.
    regards

    Comment

    • SatWaveDude
      Board Senior Member
      • Apr 2012
      • 220

      #3
      Re: Can not get SkyGrabber with SkyStar S2 to work

      I spend a lot of time trying to get SkyGrabber to work but without success.
      I'm gona try SkyNet and post my findings here.
      SatWaveDude

      DM500HD, DM500+ | EMP S16/1PCP-W3 | WaveFrontier T90 | 16x SMART Titanium 0.1dB LNB's
      TechniSat SkyStar S2 PCI / SkyStar USB HD
      WaveFrontier T90 rev.2 - 28.2E | 23.5E | 19.2E | 16E | 13E | 10/9E | 3.3E | 4/5E | 0.8W | 7/8W | 12.5W

      If you find my post usefull please press the Thanks Button

      Comment

      Working...