dm500s ethernet flash failed

[thyristor44]

Re: dm500s ethernet flash failed

The serial port on both the pc and the dreambox are very easily damaged by static electricity so the cable must be connected while off before switching on. You could have damaged port of db500s.
Keep trying anyway.

[sqazilou]

Re: dm500s ethernet flash failed

i hope its not damaged, ill keep you informed if i suceed in my flash

[vimmers]

Re: dm500s ethernet flash failed

try this dreamup

[kalpikos]

Re: dm500s ethernet flash failed

You don't have to care about any IP.
Procedure for dm500 is different to dm800 or other dm.

All job must be done with null modem cable with only 3 wires as is shown in my photo.
No adapters , no usb.
Use only an old version of dreamup.
If you can't find an old version to work , tell me and i will send you ,tonight , the dreamup that works for me.

Unplug your dreambox from the mains
Disconnect all cables from dm.
Your PC must be turn off.

1. connect cable to PC and dm (com port)
2. turn on your PC and run Dreamup and then
select your correct PC Serial Port
3. Untick “Use Network”
4. Click Connect
5. When you see the on screen message “Connection Prepared, now switch on the dreambox!” now plug in your dreambox
6. Click erase Flash
7. when this done, Click Flash and navigate to the image file on your PC
8. After installation is complete, exit DreamUp
9. Unplug your dreambox from the mains and wait at least 1 min.
10. Plug in your dreambox and wait for it to boot into setup mode

If you can't connect , probably you have damaged you dm's com port or bootloader.
Try the solution with Jtag cable.
Find someone that know this job beacuse is a little complicated.

Regards

[vimmers]

Re: dm500s ethernet flash failed

You don't have to care about any IP.
Procedure for dm500 is different to dm800 or other dm.

All job must be done with null modem cable with only 3 wires as is shown in my photo.
No adapters , no usb.
Use only an old version of dreamup.
If you can't find an old version to work , tell me and i will send you ,tonight , the dreamup that works for me.

Unplug your dreambox from the mains
Disconnect all cables from dm.
Your PC must be turn off.

1. connect cable to PC and dm (com port)
2. turn on your PC and run Dreamup and then
select your correct PC Serial Port
3. Untick “Use Network”
4. Click Connect
5. When you see the on screen message “Connection Prepared, now switch on the dreambox!” now plug in your dreambox
6. Click erase Flash
7. when this done, Click Flash and navigate to the image file on your PC
8. After installation is complete, exit DreamUp
9. Unplug your dreambox from the mains and wait at least 1 min.
10. Plug in your dreambox and wait for it to boot into setup mode

If you can't connect , probably you have damaged you dm's com port or bootloader.
Try the solution with Jtag cable.
Find someone that know this job beacuse is a little complicated.

Regards

not all PC's/computers have a serial output
so he have to use a adaptor usb to serial
i have used that several times on my old db7000 and db800

[kalpikos]

Re: dm500s ethernet flash failed

not all PC's/computers have a serial output
so he have to use a adaptor usb to serial
i have used that several times on my old db7000 and db800

You have been very lucky finding an adaptor capable of connecting pc - dm, but I think the most appropriate solution for sqazilou is to find another old pc with a serial port. Because that's the problem, the serial port.

[sqazilou]

Re: dm500s ethernet flash failed

thanks kalpikos for a detailed tutorial, but i think you are right my dreambox serial port must have been damaged
because after step 5 my dreamup is stuck on “Connection Prepared, now switch on the dreambox!”

so the null modem cable only need 3 wire all other are useless ?? ill try to make one if thats the case

[kalpikos]

Re: dm500s ethernet flash failed

thanks kalpikos for a detailed tutorial, but i think you are right my dreambox serial port must have been damaged
because after step 5 my dreamup is stuck on “Connection Prepared, now switch on the dreambox!”

so the null modem cable only need 3 wire all other are useless ?? ill try to make one if thats the case

Yes my friend, only 3 wires.

2---3
3---2
5---5

all other are useless and you don't need them.

Here is an old version of DreamUP working 100% with DM500s

DreamUP.v1.2.2.0.rar

http://hero-share.com/download/10211494/DreamUP.v1.2.2.0.rar.html

[sqazilou]

Re: dm500s ethernet flash failed

yessssssssssssssssssssssssssssssssssssssssssss

finaly i managed to flash it thanks to everyone for great help Kalpikos you were right the cable was not good pin 2-3 were not crossed so i changed them and it worked great

it was sold as a "null modem" cable but it wasnt one thats what happen when you buy cheap cable

thanks again this was making me crazy

17:42:25 box type: DM500
17:42:34 Ping result: OK, box is alive and speaking to us ;-)
17:43:43 Uploading file to box...
17:51:37 calculating CRC32 on STB...
17:51:38 erasing flash...
17:52:02 box is flashing from its memory...
17:52:20 calculating CRC32 on STB's flash...
17:52:26 "flash erase"...
17:52:40 OK, flash-copy succeeded

[kalpikos]

Re: dm500s ethernet flash failed

Great news!!!
Im very happy that you made it.

Just remember for the next time that flashing is done only with dreamup and a lot of patience

[sqazilou]

Re: dm500s ethernet flash failed

Great news!!!
Im very happy that you made it.

Just remember for the next time that flashing is done only with dreamup and a lot of patience

yup that i learned very well

my damn cable was not as it was decribed it wasnt null modem crossover lesson for me dont buy anything on am*azon

i didnt understand that only 3 wire were suficient

hope this thread will help others in my case, i was so close to throw dm by window

i think now its time to close this thread and move on

thanks