Tweet
[MANUAL] VU DUO Scripts for various images & activation.
Here I leave a small manual that I did not have to be thinking as emus and configure scripts whenever makeover.
Is designed to sbox and cccam, which is what I use, but it is quite easy to adapt to other emus.
I've done in principle for 5 images, namely:
-AAF
-BLACK HOLE
-PLI
-VIX
-VTI
I know there are more images, but as these are the ones I like, in principle only do it for them. Later we'll see if I continue with the others.
In all scripts, sbox sbox.mips is renamed, and is renamed CCcam.mips CCcam.
Without further ado, we begin
.
AAF IMAGE
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / usr / ke * s
Startup Script
Path: / etc
Syntax: prueba.emu
NOTE In the following, in the names of scripts, which is in red must be respected
Activation of the script
We're going to menu. We will leave this screen:
With AAF-panel selected, press OK and leave us the following:
With SoftCam Panel selected, press again OK:
We see that the script is selected. To activate it, no more than press the green button, and after a few seconds, voilą:
Reboot and you're done
IMAGEN BLACK HOLE
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / camscript
Syntax: Ncam_prueba.sh
Activation of the script
Blue button, this leaves us:
With the directional buttons, seek our script:
It remains to OK and we will have activated the script.
IMAGEN PLI
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / etc / init.d
Syntax: This image requires two scripts. One for the reader (sbox) and one for the emu (CCCam).
Script for the reader:
cardserver.sbox
Script for the emu:
softcam.CCcam
Activation of the script
We go into Menu, Settings, SoftCam / CI. We will leave this screen:
Went on Softcam setup and click OK. Aparecerįlo following:
Select with the arrow keys on both CCcam Softcam Select, as the Select Card Server sbox to look like this:
Here we could start the softcam cardserver and separately, but the best is down to Restart Both and click OK.
Then strip the two emus:
IMAGEN VIX
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / softcam
Syntax: softcam.pruebas.sh
Activation of the script
Accede to Menu, Settings, SoftCam / CI, and this menu appears:
We went down to Softcam setup .. and click OK
You see, as is the script that we want to give select. now blue button. And we hope it will:
As you see, down Autostar and is our script. Now we activate the green button (Start), waited a few moments, and will be working.
Reboot.
IMAGEN VTI
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / script
Syntax: prueba_cam.sh
Activation of the script
Blue button, we get this:
Blue button again:
Our script is already selected. To start it, we give the green button and wait:
As always, the last thing is to reboot.
Here I leave a small manual that I did not have to be thinking as emus and configure scripts whenever makeover.
Is designed to sbox and cccam, which is what I use, but it is quite easy to adapt to other emus.
I've done in principle for 5 images, namely:
-AAF
-BLACK HOLE
-PLI
-VIX
-VTI
I know there are more images, but as these are the ones I like, in principle only do it for them. Later we'll see if I continue with the others.
In all scripts, sbox sbox.mips is renamed, and is renamed CCcam.mips CCcam.
Without further ado, we begin
.
AAF IMAGE
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / usr / ke * s
Startup Script
Path: / etc
Syntax: prueba.emu
NOTE In the following, in the names of scripts, which is in red must be respected
Activation of the script
We're going to menu. We will leave this screen:
With AAF-panel selected, press OK and leave us the following:
With SoftCam Panel selected, press again OK:
We see that the script is selected. To activate it, no more than press the green button, and after a few seconds, voilą:
Reboot and you're done
IMAGEN BLACK HOLE
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / camscript
Syntax: Ncam_prueba.sh
Activation of the script
Blue button, this leaves us:
With the directional buttons, seek our script:
It remains to OK and we will have activated the script.
IMAGEN PLI
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / etc / init.d
Syntax: This image requires two scripts. One for the reader (sbox) and one for the emu (CCCam).
Script for the reader:
cardserver.sbox
Script for the emu:
softcam.CCcam
Activation of the script
We go into Menu, Settings, SoftCam / CI. We will leave this screen:
Went on Softcam setup and click OK. Aparecerįlo following:
Select with the arrow keys on both CCcam Softcam Select, as the Select Card Server sbox to look like this:
Here we could start the softcam cardserver and separately, but the best is down to Restart Both and click OK.
Then strip the two emus:
IMAGEN VIX
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / softcam
Syntax: softcam.pruebas.sh
Activation of the script
Accede to Menu, Settings, SoftCam / CI, and this menu appears:
We went down to Softcam setup .. and click OK
You see, as is the script that we want to give select. now blue button. And we hope it will:
As you see, down Autostar and is our script. Now we activate the green button (Start), waited a few moments, and will be working.
Reboot.
IMAGEN VTI
File path of the emus:
sbox.mips, sbox.conf and users.sbox in / usr / bin
CCcam.mips in / usr / bin CCcam.cfg in / etc
Startup Script
Path: / usr / script
Syntax: prueba_cam.sh
Activation of the script
Blue button, we get this:
Blue button again:
Our script is already selected. To start it, we give the green button and wait:
As always, the last thing is to reboot.