Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

Icecrypt 3500 and Enigma2

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • skacrazy
    Newbie
    • Feb 2013
    • 3

    Icecrypt 3500 and Enigma2

    I read this is possible but can someone explain how to do this?

    Thanks
  • satjohn
    Junior Member
    • Mar 2013
    • 10

    #2
    Re: Icecrypt 3500 and Enigma2

    Hi,Ive read that the icecrypt 4000s can be modified this entails changing the bootloader
    maybe the s3500 can . best regards,satjohn.

    Comment

    • mahrkpat
      Experienced Board Member
      • Jun 2012
      • 1493

      #3
      Re: Icecrypt 3500 and Enigma2

      This is from another forum proceed at your own risk!!!

      [Basic information]

      * 220mm : image for 220mm
      * 220mm_Nand : image for the new 220mm (SD RAM 256Mbyte)
      * 260mm : image for 260mm models (common to with SD RAM 256Mbyte)
      * vfd models : image for all single tuner models with vfd display.(300mm and 260mm even with SD RAM 256Mbyte)
      * uImage : common to all single tuner models.


      [Preperation before install E2]

      1. Update your boot loader --- 'UpdateLoaderLx.x6' version(Latest version) by Booting upgrade mode.
      (Turn on your receiver while pressing CHANNEL UP button on the front panel, until SCAN message shows up
      => 'COMPLETE' message shows up, then Turn off and on)
      2.USB Memory
      * Bootable USB memory required.
      * File system must be FAT32. (Recommend FAT32 format in advance)
      * High performacne USB memory recommended.
      (If USB memory stick is old or performace is low, USB booting can be failed.)


      [E2 Installation]

      1. Save uImage (common to all models) and root.img (specific to each model) to your USB memory.
      2. Connect the USB memory stick to receiver. (Rear or Front side)
      3. Turn on the receiver with pressing CHANNEL DOWN button on the front panel, until SCAN message shows up.
      4. The front display will show 'ON' first, then keep showing some messages more.
      * 'ON' means that reading E2 image from the USB memory is started.
      5. 'ENIGMA2' logo displays for a while.
      6. After displaying E2 logo, if your screen is black, select output mode by pressing channel Up & Down button on your RCU.
      Once select your output mode, press OK button to adapt it.
      (Currnet output mode will display on your front LCD or VFD)
      C = Component
      H = HDMI
      HC = HDMI-PC
      S = Scart

      6. Now Enjoy E2 !
      ** After installation is finished well, E2 is available whenever your USB memory is connected to receiver before turn-on.


      !!!!! [Important Notice] !!!!!

      * Do not dis-connect USB memory from the receiver while E2 is working.
      * When turn off the receiver, go to deep standby mode by pressing power button for 4seconds (RCU).
      If not, channel date couldn't be saved and/or booting fail could happen.
      In case of booting fail, you have to turn off/on & reboot 1~2times to recover.


      <Roll back to original S/W>
      1. Turn-off receiver
      2. Dis-connect USB memmory from the receiver, then turn-on the receiver.


      Copy and pasted from another forum.. Not my own tutorial
      Liked my post then push the sigpic button.

      Comment

      Working...