Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

ThThe idiots guide to updating your Spiderbox HD

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bledi07
    Experienced Board Member
    • Jun 2010
    • 824

    ThThe idiots guide to updating your Spiderbox HD

    The idiots guide to updating your Spiderbox HD
    To access the USB Menu >> Accessory >> USB >>

    A/ Insert an usb pen drive into your Spiderbox format to FAT32
    B /Press the yellow button to format the usb stick to FAT32
    C/ Now back up your channel list:
    D/ Press the green button & select Channel Data (UDB) press OK
    exit...exit

    Now place the USB stick in your pc
    Save your channel list to a document on your pc as a back up & remove the file from the USB stick,

    Make sure that you select the correct file to download for your receiver:-

    SpiderBox 9000HD
    Spiderbox 7000HD
    Spiderbox 5000SD

    1/ Down load the latest key patch & or software upgrade to your pc desktop,
    3/ Open the file by moving the mouse pointer to the compressed file,
    4/ Right click with the mouse button on the compressed file & select extract here,
    5/ Now right mouse click on the unpacked file,
    6/ Send the file to your USB stick

    Once you have loaded your files then left click on the usb device,
    Wait for the message that tells you it is now safe to remove the USB stick,

    Now place the USB stick back in the SpiderBox

    Menu >> Accessory >> USB >>

    Move the cursor down to the file that you want to download from the USB stick
    Now follow the on screen instructions,
    After you have updated your receiver it will reboot,

    Finished,


    If the Instructions with the file advised a factory reset after down loading the files & or reset of the keys in Key Edit {reset key data} file:-

    Always save your channel list before you do a factory reset as any information will be lost such as:
    TV channel lists & your Biss keys will be restored here if you were also instructed to reset the keys.
    Any Biss keys that you have saved will be lost & a 92 file list of Biss keys will replace yours

    Menu >> Installations >> Factory Reset >>Follow onscreen instructions.

    How to delete a satellite on a Spiderbox
    How to delete a satellite on the Spiderbox HD
    Go to the Satellite you want to delete,

    Part-1
    1/Installations
    2/Manual Scan
    3/Delete all transponders

    Part-2
    Installations
    Satellite Search
    Press green button & move cursor with yellow button
    Delete channel name exit & save

    Part-3
    Installations
    Motor set up
    store all un wanted satellites select 000.0 E & Exit

    The Satellite has now been removed from your Satellite List,

    You will not see the Satellite list now until you press Satellite on your Remote Control then move the cursor up or down to select a Satellite from the stored satellites in your receiver.

    How to update your Transponder Data Base
    How to update your Data Base,

    Part-1
    How to delete a transponder on the Spiderbox 7000HD - 9000HD

    1st select the satellite you want to edit by selecting a satellite from the list,
    Then follow this simple proceedure,

    1/ Menu
    2/ Installations
    3/ Manual Scan
    4/ Frequency
    5/ Now move the cursor through the list of Transponders & if the S=Green Signal Bar & Q=Blue Quality bars are showing the transponder is active so move to the next transponder,

    So move to the next transponder >>> using the cursor until you come to a transponder that is not active you will know it is not active when only the Red Signa bar lights up & nothing shows on the quality bar,
    Give it a few seconds before you delete the transponder by pressing the Yellow buttion =TP delete

    The sequence will continue in a natural progression >>> so go to the next transponder in the data base of the satellite & continue editing using the Cursor as before >>>
    If both S=Signal & Q= Quality bars are Red then dellete this transponder also via the Yellow button as the wrong data is stored,

    If you accidently remove an active transponder that you wanted to save then press Exit & choose your options {Are you sure to save?) if you select "No" then you can start again if you select "Yes" your data base will update removing the transponders that you have deleted,


    Part-2
    How to update your transponders,

    1/Menu
    2/Installations
    3/ Satellite Search
    4/ Move the Cursor down to Search Options (Here you have several options) by moving the Cursor >>>
    One TP
    Free
    Network Scan (You vcan use this option on Astra Satellites)
    TV Only
    Blind Scan

    5/Select Blind Scan then move to Start Search
    6/Set Frequency Start 10700
    7/Set Frequency end 12750
    8/Set step Value of 2-4-6-8 or 10 (Use 8 for now)
    9/Set Polarization {Use all for now with normal broadcast satellites)
    10/Choose search option {All--Free Only --TV Only} choose All for now,

    Use this Chart to select what part of the Ku band to scan,

    For example:
    Astra 28.2 east 10700 to 10950 + 11200 to 12650 for normal tv channels
  • bledi07
    Experienced Board Member
    • Jun 2010
    • 824

    #2
    Re: ThThe idiots guide to updating your Spiderbox HD

    Motor Set up control explained
    Recalculate in Motor Setup >> Command menu is to reset the motor position so that the motor knows where it is,
    This is best done on your reference satellite,
    To Access:-
    Go to Motor Set up in Installation,
    Command now select the options below by moving through the menu with your cursor >>>:-
    Also in this menu you can set:-
    Go to Sat Position (can be used to move the motor when setting up on a new reference satellite)
    Goto Centre (for setting up your reference satellite)
    Limit Off (If the Motor stops before it reaches a satellite due to restrictions on limit previously set)
    Set East Limit (sets as far as you want the motor to travel to prevent damage to dish)
    Set West Limit as above,
    Recalculate Position (when setting up reference satellite so that it is stored)

    Comment

    • bledi07
      Experienced Board Member
      • Jun 2010
      • 824

      #3
      Re: ThThe idiots guide to updating your Spiderbox HD

      How to Set Up USALS for a DiSEqC Motor
      Guide to setting up USALS on a Spiderbox HD Satellite Receiver

      Drive your dish to your reference Satellite in East of England & the Midlands this is 1 west Intelsat 10-02 now with your remote follow the instructions below:

      1/Go to Installations,
      2/Motor Set Up
      3/Press the Green Button
      4/Set your Longitude 000.5 E
      5/Set your Latitude 52.0 N

      Exit
      Stay in the Installations menu to add channels to your reference Satellite
      Go to Satellite Search
      Move cursor down to >>> Search Option
      Choose from:-
      All
      One TP
      Free Only
      Network Scan
      TV Only
      Blind scan

      Press OK when the scan is completed

      Exit & View

      To Add another satellite >>

      Using the remote:
      Menu >> Installations >>> Satellite search >> select a satellite from the list preferable next to your reference satellite for example Astra 4A @ 4 .8 east move the cursor up until you find this satellite {It may be called Sirius 4 if you have an old data base}
      Press ok in USALS the motor will now move to the new satellite >>choose scan method in search options>>more cursor start search>>when the search has finished you will be prompted to press ok
      You can now view the tv channels stored.

      Comment

      • bledi07
        Experienced Board Member
        • Jun 2010
        • 824

        #4
        Re: ThThe idiots guide to updating your Spiderbox HD

        Updating a Transponder Data Base
        Updating the data base on each satellite,

        Installations>>Menu>> Manual Scan>> Frequency>>
        Now move the cursor through the stored frequencies>>>if the frequency is active the Green Signal & Blue Quality bars will move this means that the transponder is active & ok so moving the cursor >> to the next transponder >>when you find a transponder frequency with only Red Signal & No Quality level this is a dead transponder to remove by pressing the yellow button =TP delete move onto the next transponder >> exit & save =Yes

        Howto update after you have deleted a satellite transponder data base,
        1/Installations
        2/Satellite search
        3/Search option
        4/Blind scan
        5/start search
        6/Frequency start =12500
        7/Frequency stop =12750
        8/Step value =8
        9/Polarization =All
        10/Saerch Option=All
        11/Start Search=OK


        How to edit a TV channel list:
        Menu
        Channel Manager press ok
        Move cursor to CH-Rem = delete
        Press the Red button to see if the channel clears (This may take 2 to 3 sec)
        If the channel does not clear then press OK to delete
        Press the Red button again
        Now continue through the list by pressing ok using the Red button to check if the channel will clear.
        Now Press the Blue button to confirm deletion of tv channels that you have ticked
        Exit & Save = Yes Press OK
        Exit

        To Edit Radio stations select Radio with the remote
        Select Radio on your rwmote
        Menu
        Channel manager
        Go to CH Rem
        Use the Red button to see if the Radio channel is active
        If the channel does not clear then press OK to delete
        Press the Red button again
        Now continue through the list by pressing ok using the Red button to check if the channel will clear.
        Now Press the Blue button to confirm deletion of Radio channels that you have ticked
        Exit & Save = Yes Press OK
        Exit

        To Move a TV or Radio channel
        Menu
        Channel manager
        Select the channels you want to Move by pressing OK with your remote
        Move the cursor to where you want to move the channel then press the green button
        Exit & save= Yes

        You can also move a batch of channels by this method.

        Comment

        • bledi07
          Experienced Board Member
          • Jun 2010
          • 824

          #5
          Re: ThThe idiots guide to updating your Spiderbox HD

          Setting your Reference Satellite
          Your Reference satellite is the satellite at the centre of viewable part of the Geostationary satellite arc" the Clarke Belt" regardless of obstructions,

          You need to choose a Satellite that is central to your location East to West this is your Longitude,

          Your Latitude is determined by your North South Location,

          Example If you are in:-

          Central London your Latitude is 51.32 North & Longitude is 0.5 West & Thor @ 0.8 west is your reference Satellite.

          Place Name--Country__--Latitude Longitude Reference satellite

          Barcelona, Spain 41.23 N 2.9 E-------Astra-4A @ 4.8 East

          Birmingham, England 52.25 N 1.55 W ----Thor 5 @ 0.8 West

          Belfast, Northern Ireland 54.37 N 5.56 W----Atlantic-3 @ 5 west

          Berlin, Germany --------- 52.30 N 13.25 E----HotBird @ 13 east

          Bristol, England 51.28 N 2.35 W----Atlantic-3 @ 5 west or Thor-5 @ 0.8 West

          Central London 51.32 N 0.5 West---Thor @ 0.8 west

          Dublin, Ireland ------------53.20 N 6.15 W----Atlantic-3 @ 5 West

          Edinburgh, Scotland 55.55 N 3.10 W---Atlantic-3 @ 5 west or Thor-5 @ 0.8 West

          Glasgow, Scotland 55.50 N 4.15 W---Atlantic-3 @ 5 West

          Hamburg, Germany 53.33 N 10.2 E----Eutelsat W2A @ 10 East

          Lyons, France 45 45.00N 4.50 E---Astra-4A @ 4.8 East

          Manchester, England 53.30 N 2.15 W-- Thor-5 @ 0.8 West

          Milan, Italy -------- 45.27 N 9.10 E----Eutelsat W2A @ 10 East

          Newcastle-on-Tyne 54.58 N 1.37 W--Thor-5 @ 0.8 West

          Rome, Italy-------- 41.54 N 12.27 E-- Hotbird @ 13 East

          Comment

          • bledi07
            Experienced Board Member
            • Jun 2010
            • 824

            #6
            Re: ThThe idiots guide to updating your Spiderbox HD

            How to add new Biss keys.

            Go to Menu - Key Edit -Press OK - CAS Type --> BISS -
            Press add (yellow button) - add the frequency of the channel and then put the keys on the key data pressing OK - then Exit -Save -OK - Save again -OK -Exit.
            Channel clears.

            PVR function.

            Go to PVR menu.
            Here you can set the recording size and turn off/on the Timeshift.
            To record press the Record button on the remote. To end recording press the Stop button on the remote.
            To review the recording press the Play button on the remote. A list of all your recordings will appear.
            Choose the recording that you want to watch and select it using the OK button.
            You can pause,forward or rewind.
            To return to TV press the Stop button.

            You can record using the EPG by pressing the green button.
            Select channel and press the REC key.
            If you want to Timeshift,still when a recording is in progress,press the pause button.
            To resume watching, press the Play button.

            You can Timer record using the Timer option in the menu.
            Select the Timer Index - untill 7 recordings can be scheduled.
            Set Active to 'Recording'.
            Set channel, Start Time and Duration and then exit.

            Comment

            • bledi07
              Experienced Board Member
              • Jun 2010
              • 824

              #7
              Re: ThThe idiots guide to updating your Spiderbox HD

              CCcam and NewCam Cfg
              Cfg for CCcam and New Camd only by USB
              This is another fantastic option of SpiderBox,,,

              Puting The C line in text .

              for example only By USB ..

              You write in Text files your C line
              Like

              C: ***-no-ip.info 12000 user1 user2



              Mean for CCcam for example

              CCcam

              Name or IP = ***-no-i.info
              Port= 1200
              ID=user1
              Pass=user2


              This help comes direct for Spider members.


              Don't forget to unzip first,,,

              JUST USE USB STICK to drop in your box.
              Attached Files

              Comment

              • bledi07
                Experienced Board Member
                • Jun 2010
                • 824

                #8
                Re: ThThe idiots guide to updating your Spiderbox HD

                Adding a Satellite to the Spiderbox data base
                Go to Installations >> Satellite >>look through the list of stored satellites if the satellite you require is there then click on it & scan an active transponder for the satellite to become active,
                If the satellite is a new one that is not in the data base then you can add it,
                Find a vacant slot then name the satellite & save it >> now go manual scan & add a known active transponder & scan for the new satellite to become active.

                Comment

                • zoran89
                  Experienced Board Member
                  • Mar 2010
                  • 1618

                  #9
                  Re: ThThe idiots guide to updating your Spiderbox HD

                  Originally posted by bledi07
                  The idiots guide to updating your Spiderbox HD
                  You realy shuld correct tihs "idiots" none must be idiot if he dont know how to work with this box.

                  Comment

                  • mikelo
                    Experienced Board Member
                    • Sep 2010
                    • 1680

                    #10
                    Re: ThThe idiots guide to updating your Spiderbox HD

                    Spiderbox HD 9000 Combo Manual
                    Attached Files

                    Comment

                    Working...