Tweet
Sharing TM HD
Server Settings
1st Turn on the
2nd Go to settings network adapter
* Main menu -> Setup -> System -> Network -> Adapter settings
3. ‘Use DHCP’
4. Change the 4th part of the IP address (NEVER CHANGE THE OTHER 3 PARTS OF THE IP ADDRESS)
For example: 192.168.1.159 (with DHCP On) -> 192.168.1.211 (with DHCP Off)
5. The message "STARTING..." will appear on the front panel
6. Press the OK button a few times on the front panel until the message "Checking Key" appears
7. Check the IP Address
*In this example, it is 192.168.1.211
8. Open the web browser in your computer (Internet Explorer, etc)
9. Enter the IP Address (from step 8) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):
10. Click on CCcam Edit and then you will see this:
11. In ‘Add Line at the bottom...’ type “SERVER LISTEN PORT : 45000” in the white box and then click on Add Line
*You can change the Port value from 20000 ~ 60000 (recommended)
12. Click on Previous Page
13. Type “F: Id password 0 0 0” in the white box and then click on Add Line
* It needs a temporary ID & Password for the Slave. For the ID & Password use only letters (a,c,B,N…..) & numbers (1,2,3….) but not any special characters (!,@,#,$......)
For example, if the ID is user1 and password is pass1 :
F: user1 pass1 0 0
14. Click on Previous Page
15. If you have 2 or more slaves, repeat steps 14 & 15, for example, if there are 3 slaves:
F: user1 pass1 0 0 0
F: user2 pass2 0 0 0
F: user3 pass3 0 0 0
16. Turn the Power Off and On
17. Set/Link the port between the Router and the receiver
*Check the router’s manual for Port forwarding
*Search ‘Port Forwarding and your Router’s model’ in ******, for example: ‘bt 2700hgv port forwarding’
Client Settings
1. Turn ON the receiver
2. The message "STARTING..." will appear on the front panel
3. Press the OK button a few times on the front panel until the message "Checking Key" appears
4. Check the IP Address
5. Open the web browser in your computer (Internet Explorer, etc)
6. Enter the IP Address (from step 4) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):
7. Click on CCcam Edit, and then you will see this:
8. In ‘Add Line at the bottom...’ type “C: Master’s static IP 45000 user1 pass1” in the white box and then click on Add Line, for example:
* Check the Master’s Static IP in step 10 of <Master setting>
* If the Master’s static IP is 211.144.178.211 and the Slave is No 3, therefore you should type:
C: 211.144.178.211 45000 user3 pass3
* You should check the Master’s SERVER LISTEN PORT (see Step 12 of <Master setting>)
If the Listen Port is 35000, type as follows:
C: 211.144.178.211 35000 user1 pass1
9. Click on Previous Page
10. Turn the Power Off and On
Now if you see somthing like this in your reciver ?
If you do and you don't have a motor on your dish, you just have to tell what providers do you use on which satellite and i will send you a custom made C line that will filter uneeded providers
If you don't you have first to patch your reciver
Server Settings
1st Turn on the
2nd Go to settings network adapter
* Main menu -> Setup -> System -> Network -> Adapter settings
3. ‘Use DHCP’
4. Change the 4th part of the IP address (NEVER CHANGE THE OTHER 3 PARTS OF THE IP ADDRESS)
For example: 192.168.1.159 (with DHCP On) -> 192.168.1.211 (with DHCP Off)
5. The message "STARTING..." will appear on the front panel
6. Press the OK button a few times on the front panel until the message "Checking Key" appears
7. Check the IP Address
*In this example, it is 192.168.1.211
8. Open the web browser in your computer (Internet Explorer, etc)
9. Enter the IP Address (from step 8) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):
10. Click on CCcam Edit and then you will see this:
11. In ‘Add Line at the bottom...’ type “SERVER LISTEN PORT : 45000” in the white box and then click on Add Line
*You can change the Port value from 20000 ~ 60000 (recommended)
12. Click on Previous Page
13. Type “F: Id password 0 0 0” in the white box and then click on Add Line
* It needs a temporary ID & Password for the Slave. For the ID & Password use only letters (a,c,B,N…..) & numbers (1,2,3….) but not any special characters (!,@,#,$......)
For example, if the ID is user1 and password is pass1 :
F: user1 pass1 0 0
14. Click on Previous Page
15. If you have 2 or more slaves, repeat steps 14 & 15, for example, if there are 3 slaves:
F: user1 pass1 0 0 0
F: user2 pass2 0 0 0
F: user3 pass3 0 0 0
16. Turn the Power Off and On
17. Set/Link the port between the Router and the receiver
*Check the router’s manual for Port forwarding
*Search ‘Port Forwarding and your Router’s model’ in ******, for example: ‘bt 2700hgv port forwarding’
Client Settings
1. Turn ON the receiver
2. The message "STARTING..." will appear on the front panel
3. Press the OK button a few times on the front panel until the message "Checking Key" appears
4. Check the IP Address
5. Open the web browser in your computer (Internet Explorer, etc)
6. Enter the IP Address (from step 4) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):
7. Click on CCcam Edit, and then you will see this:
8. In ‘Add Line at the bottom...’ type “C: Master’s static IP 45000 user1 pass1” in the white box and then click on Add Line, for example:
* Check the Master’s Static IP in step 10 of <Master setting>
* If the Master’s static IP is 211.144.178.211 and the Slave is No 3, therefore you should type:
C: 211.144.178.211 45000 user3 pass3
* You should check the Master’s SERVER LISTEN PORT (see Step 12 of <Master setting>)
If the Listen Port is 35000, type as follows:
C: 211.144.178.211 35000 user1 pass1
9. Click on Previous Page
10. Turn the Power Off and On
Now if you see somthing like this in your reciver ?
If you do and you don't have a motor on your dish, you just have to tell what providers do you use on which satellite and i will send you a custom made C line that will filter uneeded providers
If you don't you have first to patch your reciver
.
Comment