oscam and satlover

[knap92]

Re: oscam and satlover

Is great bokkie nice to hear that......i like and know to learn more and more ....for me Cccam it was just put cline and see tv ...but with oscam i see more thing....hoop will learn fast with this emu...

Regards

[KVF1966]

Re: oscam and satlover

Hi knap92. You download the zip file, unpack it and see the yellow folder of the Plugin. This folder copy to a flash card and connect the USB receiver. Further according to the instructions on the receiver.

[knap92]

Re: oscam and satlover

Hey KVR1966,

Oke i wil try this on my openbox 12 HD PVR....I m really curieus if *oscam will work on openbox .......

[asus7]

Re: oscam and satlover

Hello everyone!
I apologize for my English ... I wanted to ask you a question: this configuration is also valid for premium server? I tried but does not go ... It is likely that there are limitations?

[bokkie]

Re: oscam and satlover

It worked for my server 2 line. Did you us the cccam to oscam converter?

[duhoki]

Re: oscam and satlover

Hello everyone!
I apologize for my English ... I wanted to ask you a question: this configuration is also valid for premium server? I tried but does not go ... It is likely that there are limitations?

If you take a look at the log file of oscam, what dos it say? Maybe you can post your oscam config file and we can see if any problem.

[asus7]

Re: oscam and satlover

If you take a look at the log file of oscam, what dos it say? Maybe you can post your oscam config file and we can see if any problem.

Thanks for your response!

The error I see in the log is as follows: "can't resolve ***.***.***, error: Temporary failure in name resolution"

and this is my oscam.server:

[reader]
label = ***
protocol = cccam
device = ***.***.***,(port number)
user = username
password = password
inactivitytimeout = 30
group = 1
emmcache = 1,1,2
cccversion = 2.0.11
cccmaxhops = 3
cccwantemu = 1
ccckeepalive= 1

obviously the configuration concerns the two cline.

[duhoki]

Re: oscam and satlover

That happens when it is wrong port number or if the adress is offline. Could you just try with a cline from server 3, just to check that there is no config problem. Also try with only one server active. Use same group etc...

[KVF1966]

Re: oscam and satlover

Here is an example of a working Oscam
[reader]
label=cccam.satlover.com
enable=1
protocol=cccam
device=cccam.satlover.com,***xx
user=******xx_******xx
password=www.satlover.com
cccwantemu=0
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
cccwantemu=1
ccckeepalive=1

[gianni253]

Re: oscam and satlover

Here is an example of a working Oscam
[reader]
label=cccam.satlover.com
enable=1
protocol=cccam
device=cccam.satlover.com,***xx
user=******xx_******xx
password=www.satlover.com
cccwantemu=0
cccversion=2.1.2
group=1
inactivitytimeout=1
reconnecttimeout=30
lb_weight=100
cccversion=2.1.2
cccmaxhops=10
cccwantemu=1
ccckeepalive=1

cccwantemu should be set to "0" OR to "1" (not both directives)

[ZoxPa]

Re: oscam and satlover

You can set cccwantemu=0. Satlover is not using emu over cccam.

[ocin]

Re: oscam and satlover

Os*am 1.20 unstable build 8079 with cc*am 2.3.0 on a dreambox 600 with Sifteam 1.9.4c.
It works fine for me and more stable then cc*am alone.
Configuration by web page is so easy.

[BlueIsMyColor]

Re: oscam and satlover

one question: is it possible to limit the shares only to hop1 in a specific provider over oscam?

[ZoxPa]

Re: oscam and satlover

one question: is it possible to limit the shares only to hop1 in a specific provider over oscam?

No, limit is general for all providers in one reader.

[parsonline]

Re: oscam and satlover

It worked for my server 2 line. Did you us the cccam to oscam converter?

you dont need to convertor. after you install oscam you found oscam.server and enter server information and user and pass and then save your setting
and after that start emu.