Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

Smargo readers

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • Boxaren
    Junior Member
    • Nov 2012
    • 14

    Smargo readers

    Hi
    I have done all the configuration with oscam and are now entering up with the final check to verify that i have done everything corrrect.
    Now i was hitting a new problem.
    My readers connected to USB are not running, i have checked by lsusb and dmesg and they are attached to ttyusb 0&1 but i am reciving latnecy timer -32.
    If i go in and checking in the device manager i have no attached devices to usb, if i try with a memory stick the stick apperas but not my readers.
    It seams that Ubuntu has not configured it some way or i have not done my homework.
    Please could anybody tell me how i should do to have the readers active in my linux pc 32bits. Ubuntu version

    Logg:

    [ 0.097206] usbcore: registered new interface driver usbfs
    [ 0.097259] usbcore: registered new interface driver hub
    [ 0.097491] usbcore: registered new device driver usb
    [ 0.839466] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.839579] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.839632] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.846499] uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
    [ 0.847379] hub 1-0:1.0: USB hub found
    [ 0.848167] uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
    [ 0.848991] hub 2-0:1.0: USB hub found
    [ 1.188912] usb 1-1: new full speed USB device number 2 using uhci_hcd
    [ 1.480501] usb 1-2: new full speed USB device number 3 using uhci_hcd
    [ 388.184511] usbcore: registered new interface driver usbserial
    [ 388.198655] USB Serial support registered for generic
    [ 388.199559] usbcore: registered new interface driver usbserial_generic
    [ 388.199575] usbserial: USB Serial Driver core
    [ 388.243819] USB Serial support registered for FTDI USB Serial Device
    [ 388.247250] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [ 388.248717] usb 1-1: Detected FT232BM
    [ 388.248738] usb 1-1: Number of endpoints 2
    [ 388.248747] usb 1-1: Endpoint 1 MaxPacketSize 64
    [ 388.248757] usb 1-1: Endpoint 2 MaxPacketSize 64
    [ 388.248766] usb 1-1: Setting MaxPacketSize 64
    [ 388.250310] ftdi_sio ttyUSB0: Unable to read latency timer: -32
    [ 388.265076] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
    [ 388.265184] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
    [ 388.266266] usb 1-2: Detected FT232BM
    [ 388.266288] usb 1-2: Number of endpoints 2
    [ 388.266298] usb 1-2: Endpoint 1 MaxPacketSize 64
    [ 388.266307] usb 1-2: Endpoint 2 MaxPacketSize 64
    [ 388.266316] usb 1-2: Setting MaxPacketSize 64
    [ 388.270018] ftdi_sio ttyUSB1: Unable to read latency timer: -32
    [ 388.285229] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB1
    [ 388.288760] usbcore: registered new interface driver ftdi_sio
    [ 388.288781] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
    [55477.272185] usb 1-1: USB disconnect, device number 2
    [55477.272789] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
    [55479.496106] usb 1-1: new full speed USB device number 4 using uhci_hcd
    [55479.658685] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [55479.658953] usb 1-1: Detected FT232BM
    [55479.659252] usb 1-1: Number of endpoints 2
    [55479.659264] usb 1-1: Endpoint 1 MaxPacketSize 64
    [55479.659273] usb 1-1: Endpoint 2 MaxPacketSize 64
    [55479.659283] usb 1-1: Setting MaxPacketSize 64
    [55479.662110] ftdi_sio ttyUSB0: Unable to read latency timer: -32
    [55479.664402] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
    [57341.984160] usb 1-1: USB disconnect, device number 4
    [57341.984745] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
    [57344.712166] usb 1-2: USB disconnect, device number 3
    [57344.712799] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
    [57347.644130] usb 1-2: new full speed USB device number 5 using uhci_hcd
    [57347.811522] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
    [57347.811788] usb 1-2: Detected FT232BM
    [57347.811802] usb 1-2: Number of endpoints 2
    [57347.811812] usb 1-2: Endpoint 1 MaxPacketSize 64
    [57347.811822] usb 1-2: Endpoint 2 MaxPacketSize 64
    [57347.811831] usb 1-2: Setting MaxPacketSize 64
    [57347.814014] ftdi_sio ttyUSB0: Unable to read latency timer: -32
    [57347.816700] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0
    [57354.128150] usb 1-1: new full speed USB device number 6 using uhci_hcd
    [57354.295652] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [57354.295923] usb 1-1: Detected FT232BM
    [57354.295935] usb 1-1: Number of endpoints 2
    [57354.295944] usb 1-1: Endpoint 1 MaxPacketSize 64
    [57354.295953] usb 1-1: Endpoint 2 MaxPacketSize 64
    [57354.296273] usb 1-1: Setting MaxPacketSize 64
    [57354.299494] ftdi_sio ttyUSB1: Unable to read latency timer: -32
    [57354.301269] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB1
    [57529.472176] usb 1-1: USB disconnect, device number 6
    [57529.472802] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
    [57536.408126] usb 1-1: new full speed USB device number 7 using uhci_hcd
    [57536.853788] usbcore: registered new interface driver uas
    [57536.881441] Initializing USB Mass Storage driver...
    [57536.882066] scsi2 : usb-storage 1-1:1.0
    [57536.882632] usbcore: registered new interface driver usb-storage
    [57536.882646] USB Mass Storage support registered.
    [57593.952183] usb 1-1: USB disconnect, device number 7
    [57603.864121] usb 1-1: new full speed USB device number 8 using uhci_hcd
    [57604.027238] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [57604.027571] usb 1-1: Detected FT232BM
    [57604.027584] usb 1-1: Number of endpoints 2
    [57604.027594] usb 1-1: Endpoint 1 MaxPacketSize 64
    [57604.027603] usb 1-1: Endpoint 2 MaxPacketSize 64
    [57604.027612] usb 1-1: Setting MaxPacketSize 64
    [57604.030160] ftdi_sio ttyUSB1: Unable to read latency timer: -32
    [57604.032759] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB1
    [57625.448171] usb 1-1: USB disconnect, device number 8
    [57625.448802] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
    [57628.912118] usb 1-1: new full speed USB device number 9 using uhci_hcd
    [57629.081192] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [57629.081466] usb 1-1: Detected FT232BM
    [57629.081479] usb 1-1: Number of endpoints 2
    [57629.081488] usb 1-1: Endpoint 1 MaxPacketSize 64
    [57629.081497] usb 1-1: Endpoint 2 MaxPacketSize 64
    [57629.081507] usb 1-1: Setting MaxPacketSize 64
    [57629.082304] ftdi_sio ttyUSB1: Unable to read latency timer: -32
    [57629.084659] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB1
    [70090.424168] usb 1-2: USB disconnect, device number 5
    [70090.424779] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
    [71587.128108] usb 1-2: new full speed USB device number 10 using uhci_hcd
    [71587.291024] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
    [71587.291288] usb 1-2: Detected FT232BM
    [71587.291300] usb 1-2: Number of endpoints 2
    [71587.291309] usb 1-2: Endpoint 1 MaxPacketSize 64
    [71587.291318] usb 1-2: Endpoint 2 MaxPacketSize 64
    [71587.291383] usb 1-2: Setting MaxPacketSize 64
    [71587.294874] ftdi_sio ttyUSB0: Unable to read latency timer: -32
    [71587.296607] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0
    [72020.856190] usb 1-1: USB disconnect, device number 9
    [72020.856817] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
    [72023.088177] usb 1-2: USB disconnect, device number 10
    [72023.088787] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
    [72485.872129] usb 1-1: new full speed USB device number 11 using uhci_hcd
    [72486.039502] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
    [72486.039767] usb 1-1: Detected FT232BM
    [72486.039779] usb 1-1: Number of endpoints 2
    [72486.039789] usb 1-1: Endpoint 1 MaxPacketSize 64
    [72486.039799] usb 1-1: Endpoint 2 MaxPacketSize 64
    [72486.039808] usb 1-1: Setting MaxPacketSize 64
    [72486.041990] ftdi_sio ttyUSB0: Unable to read latency timer: -32
    [72486.043993] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
    [72490.808114] usb 1-2: new full speed USB device number 12 using uhci_hcd
    [72490.968873] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
    [72490.969148] usb 1-2: Detected FT232BM
    [72490.969159] usb 1-2: Number of endpoints 2
    [72490.969169] usb 1-2: Endpoint 1 MaxPacketSize 64
    [72490.969178] usb 1-2: Endpoint 2 MaxPacketSize 64
    [72490.969186] usb 1-2: Setting MaxPacketSize 64
    [72490.970408] ftdi_sio ttyUSB1: Unable to read latency timer: -32
    [72490.972521] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB1
    root@Klient:~#

    And readers:
    [reader]

    label = Supplier 1
    enable = 1
    protocol = smargo
    device = ttyUSB0
    aeskey = 0102030405060708090a0b0c0d0e0f10
    group = 1 # card one
    caid = 0700
    emmcache = 1,3,2


    [reader]

    label = Supplier 2
    enable= 1
    protocol = smargo
    device = ttyUSB1
    aeskey = 0102030405060708090a0b0c0d0e0f10
    group = 2 # two cards
    boxid = ******XX
    caid = 093E
    emmcache = 1,3,2
  • Boxaren
    Junior Member
    • Nov 2012
    • 14

    #2
    Re: Smargo readers

    My latest reader settings by try and error.....
    label = sat1
    enable = 1
    protocol = smartreader+
    device = /dev/ttyUSB0
    detect = ring
    mhz = 357
    cardmhz = 357
    aeskey = 0102030405060708090a0b0c0d0e0f10
    group = 1
    caid = 0B00
    emmcache = 1,3,2


    [reader]

    label = sat2
    enable= 1
    protocol = smartreader+
    device = /dev/ttyUSB1
    detect = ring
    mhz = 357
    cardmhz = 357
    aeskey = 0102030405060708090a0b0c0d0e0f10
    group = 2
    boxid = 823F4B8F #fake number
    caid = 093E
    emmcache = 1,3,2

    Comment

    • Boxaren
      Junior Member
      • Nov 2012
      • 14

      #3
      Re: Smargo readers

      Solved by settings below in win environment, since i never got my Linux to work.
      But what i need to do was to change my protocol to mouse and move my com port settings to 20 and 25 in the win pc and change them in the server file to 19 and 24.
      Then it was working.
      label = cd
      enable = 1
      protocol = mouse
      device = /dev/ttyS24
      detect = cd

      Comment

      Working...