User guide for OSCAM

[porche944]

I'm struggling to set up OSCAM on my Vu+Duo.

Could anyone post a guide on how to set it up?

Thanks.

[matrixneo12]

Re: User guide for OSCAM

hi do you want to set up Oscam as Cardreader server or just as reader for your C-Lines?

[porche944]

Re: User guide for OSCAM

I would like it to be a reader and I see it can be a client as well. But if it easier for it support C-Line then that's OK to.

Thanks.

[uttnls]

Re: User guide for OSCAM

I would like it to be a reader and I see it can be a client as well. But if it easier for it support C-Line then that's OK to.

Thanks.

Whi do you want to use Oscam, do you try to read some cards that are not suported yet on CCcam or what are you trying to do ?

[matrixneo12]

Re: User guide for OSCAM

Oscam as reader for C-Line(cccam server)

config file oscam.server in your box as folow:

[reader]
label = mycccamreader
protocol = cccam
device = server ip,serverport
account = user,password
group = 1
caid = 0300,0400,0500,4AE1 use this entry only if you want to determine the caids which you want to receive.

[housy01]

Re: User guide for OSCAM

The best user guide is the oscam official wiki.
You can find it on ****** the the words "oscam wiki".

[mochaart]

Re: User guide for OSCAM

Here's the link to english Oscam Wiki page
_http://streamboard.gmc.to/wiki/index.php/OSCam/en

Additionally, there's german, french & italian version as well.

[guli]

Re: User guide for OSCAM

I'm struggling to set up OSCAM on my Vu+Duo.

Could anyone post a guide on how to set it up?

Thanks.

here is an example
anything in red you can change to your need .

Oscam.server

[reader]
label = skyuk
protocol = internal
enable = 1
device = dev/sci0
caid = 0963
boxid = ******xx ( not needed as oscam can read boxid )
detect = cd
mhz = 500
cardmhz = 500
ident = 0963:000000
group = 1
emmcache = 1,3,2
blockemm-g = 1
blockemm-unknown = 1
lb_weight = 101

Oscam.conf


[global]
logfile = /var/local/oscam.log
cachedelay = 120
nice = -1
maxlogsize = 0
saveinithistory = 1

[newcamd]
port = 15500@0963:000000
key = 0102030405060708091011121314
keepalive = 1


[webif]
httpport = 15000
httpuser = user
httppwd = password
httprefresh = 10
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255

Oscam.user

[account]
user = user
pwd = pass
uniq = 2
monlevel = 1
caid = 0963
ident = 0963:000000
group = 1
au = skyuk

Use this N line in cccam.cfg if you want to use the Newcs protocol to connect to CCcam. Only use 256 if using CCCam 2.1.3 or below . to show your card as a local .

N: 127.0.0.1 15500 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256

the username & pass in account & N line must be the same .

the port number in newcamd must be the same as in your N line .

256 @ the end of the N line is to show your card as local .

with these settings your card will update providing you gave a close & known peer a C line like this :

C: myserver.dyndns.tv 13001 user pass yes

the yes @ the end is required for the known peer to send EMM to update the card .

in the F line for this peer it should look like this

F: user pass 1 0 1 { 0:0:2 }

the 2nd 1 allows the EMM to update your card .

you can see your entitlements by opening the web browser & entering the box ip with the webif port .

oscam with cccam will only show your card as local ( hop0 ) with 2.1.3 or earlier versions . cccam 2.1.3 is the better option .

make sure the config directory has 755 attribute & the 3 oscam files in that directory have attribute 644

oscam.conf
oscam.server
oscam.user

oscam will only read your card & forward it via the N line to CCcam . you then give C lines to your peers as usual .

upon putting all your settings together make sure you stop oscam then cccam via the blue panel .

restart oscam then cccam . this allows oscam to read the card before cccam .

any changes to configs in oscam will take effect upon restart of oscam

there are many other settings that you can have but this is a basic setting to get going .

guli

[mirny]

Re: User guide for OSCAM

command for changing atributes:
chmod 755 namefile

[cylib]

Re: User guide for OSCAM

Oscam as reader for C-Line(cccam server)

config file oscam.server in your box as folow:

[reader]
label = mycccamreader
protocol = cccam
device = server ip,serverport
account = user,password
group = 1
caid = 0300,0400,0500,4AE1 use this entry only if you want to determine the caids which you want to receive.

Using this setup for multiple C lines creates problems to server as all C lines take ecm from all severs simultaneously.