Not able to connect to all clines (CCCAM Strange Problem)

[dm800pvr]

Hello,

My EDG Nemesis have cccam 2.2.1 installed and included 4 clines cccam.cfg file,

Clines are:
C: azarcam.mine.nu 13000 user pass
C: azarcam3.mine.nu 14000 user pass
C: azarcam2.mine.nu 12000 user pass
C: azarcam1.mine.nu 24400 user pass

Seems that azarcam is one server and in the other side:

azarcam1-azarcam3 have the same IP but different ports,

I'm able to connect to the first cline without any problem,
But not the other 3 ( in cccam info 1 is green 3 are red)

I had 2-3 successful attempts to those 3 clines too but a very rare times and after restarting the emulator all lost but still first cline works!

I have tested 2.1.3 and other versions too but only 2.2.1 is able to connect to at least one cline.

I wounder if someone already had such a rare problem and give me a solution because it's about 2 days I'm not able to connect and make a stable connection.

Cheers

[ecsbox360]

Re: Not able to connect to all clines (CCCAM Strange Problem)

seems like an issue you should check with the server provider. I take it the numbers 1-2-3 after the server address are purely fake and added so not to give away the real server address and these are not typed like this.. as they would be 4 seperate addresses.

id check address & ports with server provider - then check valid user/pass.

[dm800pvr]

Re: Not able to connect to all clines (CCCAM Strange Problem)

thanks ecsbox,
Already did and cccam server provider says this is not an issue and many users use it without any problem,

Yes 1,2,3 is one server with different ports, I can telnet to all using the same network as my dm xbox and also yesterday for about 1 hours I was able to use all c: lines without any problem but after restarting the emulator 2.2.1 the same problem, only first c: line connected

Is there anyway to edit the config file?

[ecsbox360]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Are you able to ping the address & port ? If not your router could be blocking / incorrectly routing traffic on the port. See 'Port Forwarding'.

[boj_co]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Try another version of cccam perhaps 2.1.4, maybe then could work...

[dm800pvr]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Try another version of cccam perhaps 2.1.4, maybe then could work...

Yes! I didn't find 2.1.4 for EDG Nemesis, Only 2.1.3 and 2.2.1 available

Are you able to ping the address & port ? If not your router could be blocking / incorrectly routing traffic on the port. See 'Port Forwarding'.

Yes! I can also telnet to that IP's and ports too


Guys I'm trying to install another image,
newnigma2-snapshot-dm800-20111201040621.nfi for now,
Maybe image problem

Update: the same result
Is there any tool except that cardsharing info site to test c line and get cards infos...?

[sucan]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Try to use this configuration .

C: azarcam.mine.nu 13000 user pass
C: azarcam.mine.nu 14000 user pass
C: azarcam.mine.nu 12000 user pass
C: azarcam.mine.nu 24400 user pass

ie without 1,2 and 3 numbers at the end of the azarcam

[spanky_1209]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Try to write into your cccam.cfg c-lines just one line at the time and then you try to connect to :

exmp : --> C: azarcam3.mine.nu 14000 user pass

If you succseed one line at the time then the lines must be OK.

Personally I use tree lines at the same time with cccam 2.2.1 and I had no Problems in my Dbox 2. Everything works great.

[boj_co]

Re: Not able to connect to all clines (CCCAM Strange Problem)

If everything is okay with lines, then cccam must be connected to all c lines. If you try everything, then the only thing is that you ask your service provider why you can not connect to server (could be faulty c lines).

[fandm]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Have you tried turning off the working cline and see if you can then connect.

[dm800pvr]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Have you tried turning off the working cline and see if you can then connect.

Man that doesn't helps and no one connects,

If everything is okay with lines, then cccam must be connected to all c lines. If you try everything, then the only thing is that you ask your service provider why you can not connect to server (could be faulty c lines).

Yea it seems it works for other users and actually works 1-2 times a day for me too but disconnect again! Net speed is good and works stable!

Try to write into your cccam.cfg c-lines just one line at the time and then you try to connect to :

exmp : --> C: azarcam3.mine.nu 14000 user pass

If you succseed one line at the time then the lines must be OK.

Personally I use tree lines at the same time with cccam 2.2.1 and I had no Problems in my Dbox 2. Everything works great.

One line, all lines, working lines, not working lines test all with no success

PS1: is there any windows based software to monitor c lines
PS2: is there any command to log and monitor cccam starting and connecting process via SSH?

Thanks for all your help

[sucan]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Yea it seems it works for other users and actually works 1-2 times a day for me too but disconnect again! Net speed is good and works stable!

Ask your server provider to change your user name and password. Someone can steal your connect information and if it connect before you , you can not conect if serever allow connection from only one IP.

[dm800pvr]

Re: Not able to connect to all clines (CCCAM Strange Problem)

Ask your server provider to change your user name and password. Someone can steal your connect information and if it connect before you , you can not conect if serever allow connection from only one IP.

Nope!
I'm able to connect with all clines with HDVB 1.2.3 ! so the problem is not server,neither my net
Check attached file!

guys this is a very strange problem,
Still unsolved!

[cannon_29]

Re: Not able to connect to all clines (CCCAM Strange Problem)

I have a lot of c-lines,but i am also having the same problem with 3 c-lines,if they are connected they show 0 cards,but when i use hdvb they connect and show all cards i have nabilosat darkstar 2 cc-cam 2.1.3.what could the problem be?

[Mudassar]

Re: Not able to connect to all clines (CCCAM Strange Problem)

hi cannon_29,

i had same problem. but i tried using another ISP and i could connect all lines.i dont know whetehjer some restriction happened for ISP to connect to remote ccccam server. experts pls help....