Welcome!

Welcome to Satlover forums, full of great people, ideas and excitement.

Please register if you would like to take part. link..

Register Now

Alert: Don't Use Hotmail Email Accounts for registration

Collapse

Before Access to all Forums and Trial accounts you must need to activate your account Email address

How to install enigma 2 to ipbox 9000HD

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • anacondama
    Banned
    • Jul 2010
    • 865

    How to install enigma 2 to ipbox 9000HD

    We will need the following:

    1) null modem cable
    2) a usb stick.

    3)The programme PuTTy isi freeware and you will find it here:
    Download PuTTy

    4)The programme KCC for kathrein
    Donwload KCC

    5)The Enigma2_SifTeam_Cuberevo image for Ipbox 9000 HD

    Installation guide:

    1) We install uboot 1.3.1 and higher

    2) We turn off the ipbox 9000 from the on/off switch and we connect the null modem cable.

    3) We install the Putty programme and start the programme. Look at the bellow picture:

    4) We select serial,speed 115200 and at serial line we put the com we use. Then we push open.

    5) Then the bellow picture will appear at our PC.

    6) At the same time we switch on our Ipbox 9000, press ctrl + Z at our keyboard. Continue hitting ctrl + Z .
    If you did it right, then at putty’s window it will appear the following prompt:
    cuberevo>
    If not, switch off your receiver open again putty and do again 4), 5),6).

    7) At cuberevo> we copy paste the following (Don’t forget to customize the bellow settings to your network environment. ipaddr is the ip of your decoder, serverip is the ip of your nfs-server, gateway is your gateway ip, netmask is the mask of your home-net):

    setenv menu_1 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootargs "console=ttyAS1,115200 panic=3 bigphysarea=10240 root=/dev/nfs nfsroot=/root/Desktop/root rw rootpath=/root/Desktop/root ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 init=/bin/devinit";setenv bootcmd "nfs a5ff0000 192.168.1.6:/root/Desktop/root/boot/uImage;bootm a5ff0000";saveenv;boot'

    Push then enter and the cuberevo> prompt will appear again.
    Do the same also with:

    setenv menu_2 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 bigphysarea=10240 root=/dev/sda1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";seten v bootcmd "run bootusb";saveenv;boot'
    setenv menu_3 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 bigphysarea=10240 root=/dev/sdb1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";seten v bootcmd "run bootusb";saveenv;boot'
    setenv menu_4 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500 ip=$ipaddr:$serverip:$gateway:$netmask quiet";setenv bootcmd "bootm a0060000";saveenv;boot'
    saveenv


    8) When all is done well, at putty’s console we will get the message:
    U-Boot 1.3.1 (Jun 11 2008 - 15:53:39) - stm23-2008-03-19
    Board: cuberevo (0x2D42C041)
    Board: 12 dotmatrix vfd front
    DRAM: 128 MB
    Flash: 32 MB
    In: serial
    Out: serial
    Err: serial
    Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
    Setup mac address.
    Saving Environment to Flash...
    Un-Protected 1 sectors
    Erasing Flash...

    .
    Erased 1 sectors
    Writing to Flash... done
    Protected 1 sectors


    9) now you can restart your decoder and press the relative remote controller's button for 5 seconds to start the image you want:

    Press Button 1: start your image using nfs-server
    Press Button 2: start your image using usb pendrive if you don't have a SATA hdd
    Press Button 3: start your image using usb pendrive if you have a SATA hdd
    Press Button 4: start your original flash image in the decoder (DGStation's original firmwares and images based on them)


    10) We install KCC.
    Start KCC and set the following:

    Type your Ip adrress, username and password at the fields that been showed at above picture.
    Make a test Connection if all is OK.
    Then press at KCC toolbar the Experts button.

    Here we see our usb stick as sdb.

    Make right click at your mouse on usb’s /dev/sdb and the a menu window opens. We select new partitioner. We make 2 new partitions. The first one must be 512 mb at ext2 label and we name it XSYS1. The second partition will have the rest of usb size. Select ext2 label for it and name it XSYS2.
    Close KCC. Unplug the usb stick from receiver and place it again.

    11) Open a ftp programme. And copy paste the enigma2_cuberevo.tar.gz to
    /mnt/usb/usb0

    12) Open telnet and write:
    cd /mnt/usb/usb0
    tar xzf enigma2_cuberevo.tar.gz
    mv ./release/*
    .
    (At the second command, you will wait long)

    13) Switch OFF the receiver.
    Switch it On again and press the relative remote controller's button for 5 seconds to start the image you want:

    Press Button 1: start your image using nfs-server
    Press Button 2: start your image using usb pendrive if you don't have a SATA hdd
    Press Button 3: start your image using usb pendrive if you have a SATA hdd
    Press Button 4: start your original flash image in the decoder (DGStation's original firmwares and images based on them)


    14) First time the booting for Enigma2 will take about 10 min.

    Re-Shared Post
    EnjoY!
Working...