Tweet
Loading latest AFF image on to flash and set up motor.
First load AFF2.0d in to box using USB method.
Place Kathy in Standby mode - time and date must be on VFD of box' go in to menu and choose
Menu
Setting
Customise screen menu
Front display in standby On
Exit
Red button to standby, time comes on VFD display on box. Kathy now sleeping.
Open KathiControlCentre 3.1 (latest)
Test IP connection under 'Settings' tab press 'Test connection' button make sure you are connected. If not reboot box and menu, red button, setting for network, switch on DHCP. Test connection, if okay, then back in standby.
Open 'Flash tab' in KCC.
Click on button top right to select file '.kim' format for AFF2.0e which you have download and extracted (latest image).
Takes a while to load. Do not power down. When finished power off box at back and wait for 20 seconds, reboot in to AFF2.0e. Menu red button, setting download Usals patch.
Motor settings
This is back to front for longitude and latitude and in German in menu so FTP to box find the file /config rotor.cfg
edit file
and enter your position.
Example you are in West London then
LON=-0.17
west of 0 degrees must have minus!!!!!!!!!!!!
Anyway it worked for me.
Now you have AFF2.0e working you can format usb drive using HP format tool to fat 32 and label it 'XBA' put in front of box.
Install BA file first, then BA boot menu.
Activate and then deactivate 2nd bootloader and then load BA image on to partition. Right click to bring up menu in area which says 'Installed images' drop down menu appears, select 'Install image in partition'.
Install BA image on to partition.
Activate 2nd Bootloader.
Reboot box and then Flash menu appears, choose flash image or BA image.
BA image takes 2 minutes to load.
If enigma 2 freezes then shut down box at back and reboot in to flash image and then shutdown. If you reboot straight to e2 image then image may not load and get stuck with message 'loading modules' on vfd.
First load AFF2.0d in to box using USB method.
Place Kathy in Standby mode - time and date must be on VFD of box' go in to menu and choose
Menu
Setting
Customise screen menu
Front display in standby On
Exit
Red button to standby, time comes on VFD display on box. Kathy now sleeping.
Open KathiControlCentre 3.1 (latest)
Test IP connection under 'Settings' tab press 'Test connection' button make sure you are connected. If not reboot box and menu, red button, setting for network, switch on DHCP. Test connection, if okay, then back in standby.
Open 'Flash tab' in KCC.
Click on button top right to select file '.kim' format for AFF2.0e which you have download and extracted (latest image).
Takes a while to load. Do not power down. When finished power off box at back and wait for 20 seconds, reboot in to AFF2.0e. Menu red button, setting download Usals patch.
Motor settings
This is back to front for longitude and latitude and in German in menu so FTP to box find the file /config rotor.cfg
edit file
and enter your position.
Example you are in West London then
LON=-0.17
west of 0 degrees must have minus!!!!!!!!!!!!
Anyway it worked for me.
Now you have AFF2.0e working you can format usb drive using HP format tool to fat 32 and label it 'XBA' put in front of box.
Install BA file first, then BA boot menu.
Activate and then deactivate 2nd bootloader and then load BA image on to partition. Right click to bring up menu in area which says 'Installed images' drop down menu appears, select 'Install image in partition'.
Install BA image on to partition.
Activate 2nd Bootloader.
Reboot box and then Flash menu appears, choose flash image or BA image.
BA image takes 2 minutes to load.
If enigma 2 freezes then shut down box at back and reboot in to flash image and then shutdown. If you reboot straight to e2 image then image may not load and get stuck with message 'loading modules' on vfd.