How mgcamd is installed in dm800se enigma2?

[kalpikos]

Re: How mgcamd is installed in dm800se enigma2?

Dear tech1010

Your problem has nothing to do with the web interface.

Btw, in order to get the web interface of your box, just type your dreambox's IP in the address bar and press "Enter".

Also, if you want to see the cccam info page, type in the address bar:
dreambox's IP:16001

Info page for mgcamd doesn't exist.
You can only see some infos in the log file var/tmp , as I've already said before.

The freezing in mgcamd can be caused by many reasons:

-Maybe the image you now have, doesn't work properly with mgcamd.
-The line you have is only for use (or better working) with cccam.
-Maybe by using another version of mgcamd you will not get freezing.
-The mg_cfg is not properly optimizing and you have to edit some values.

Remember that you have to find the cause of the problem, and we, in the forum, can only make some suggestions.
Star testing your box until you find the cause of the problem.

[tech1010]

Re: How mgcamd is installed in dm800se enigma2?

by the way,

do you have a webinterface (webif) with mgcam ?
log report ?

thx

again thanks to all friends and this forum to solve my previous problem..

dear still i am using TS 1.1 SAT4FN image.. Here i have no webinterface option.. Previously i had gp3 that has option.. What is the use of webinterface option ? If any of my friend has the knowledge to solve the problem of freezing in mgcmd pls help me.. C line has no problem.. So pls solve my problem friends..

[kalpikos]

Re: How mgcamd is installed in dm800se enigma2?

by the way,

do you have a webinterface (webif) with mgcam ?
log report ?

thx

I think that the log file of mgcamd is located in var/tmp

edit...

I confused the web interface with the cccam info page as dear aplok obviusly did.

The web interface has nothing to do with the mgcamd.

[aplok]

Re: How mgcamd is installed in dm800se enigma2?

by the way,

do you have a webinterface (webif) with mgcam ?
log report ?

thx

[tech1010]

Re: How mgcamd is installed in dm800se enigma2?

Thanks to all my friends who gave me best help to open mgcamd. Now it is working.. But now one new problem is there.. There are some conax channels which open very fast and are stable in cccam but the same conax and other channels in mgcamd are with freezing. Sometimes it needs to start and restart mgcamd to play the channels. Cline ecm time is very nice.. No problem with line..pls help friends. Thanks

[kalpikos]

Re: How mgcamd is installed in dm800se enigma2?

@tech1010
What image you have?
Because some images have problems with mgcamd.

As @mahrkpat said, if you finish the installation of mgcamd, then you need to put a camd.list file in var/keys and an edit to mg_cfg (G: { 33 }).
Also, you can try a mgcamd line to see if it's working at all.

[mahrkpat]

Re: How mgcamd is installed in dm800se enigma2?

For mgcamd to work with c lines you need a camd.list file as well, it is in this that you type
or copy/paste your c line and then in mg_cfg edit G: so that mgcamd knows it is dealing
with CCcam, I suggested to set G: { 33 } like this so that it works with newcam and cccam
i.e sum 01=newcam +32=cccam=33 and you have to set permissions to 755.

[tech1010]

Re: How mgcamd is installed in dm800se enigma2?

why do you need to install both mgcam and oscam ?

oscam is required for mgcam ?

mgcam is required to enable oscam to handle mgam ?

is it mandatory for client ?
is it mandatory for server ?

thx

no dear i just need mgcamd configuration. i trying hard from last one week to get dish tv on mgcamd but still unable to get it.. My c line is working well in cccam. But in mgcamd no channel is opening.. 1. Pls one more query is how many total files are there in mgcamd or in usr/keys after installing mgcamd.
2. When i install mgcamd in softcams or from add ons. I get four files by default in usr/keys 1. Mg_cfg 2. Priority list 3. Replace. List 4. Softcam keys.. There are no other files like cccamd.list peer.cfg newcamd.list. Only then i was asking to install mgcamd manually.. Thanks.. I ll feel proud on this forum and my friends who ll guide me to solve my problem..

Did you set the permission for the file in /usr/bin?

i have no any file in usr/bin. What i have to do with this?

[aplok]

Re: How mgcamd is installed in dm800se enigma2?

why do you need to install both mgcam and oscam ?

oscam is required for mgcam ?

mgcam is required to enable oscam to handle mgam ?

is it mandatory for client ?
is it mandatory for server ?

thx

[mahrkpat]

Re: How mgcamd is installed in dm800se enigma2?

This is just a cut & paste job from me credit goes to MasterG on another forum
the only thing I am adding is that G:{33} set like this for c line and like aplok has
said for c line you need camd.list in which you copy and paste your line and the
permission of mg_cfg needs tobe set to 755 as well. It might give you idea.

How to : Mgcamd + Oscam SatelliteBG Conax
Here are working configs for SatelliteBG Conax using Mgcamd + Oscam for updating the monthly entitlements.
Oscam files can be found in folder;
/var/tuxbox/config (Enigma1)
/etc/tuxbox/config (Enigma2)
Mgcamd files can be found in folder;
/usr/keys or /var/keys/

mg_cfg

# EMM messages
#    00 don't show any EMMs (default)
#    01 show only valid EMMs
#    02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
#    00 don't show anything about ecm
#    01 normal mode, show pids processed, decoded ecm and cw
#    02 verbose mode, show valid and bad ECMs with data
C: { 02 }

# AU
#    00 disable, no emm pids processed
#    01 enable, emm pids always processed for soft-au and shared cards
#    02 auto, emm started only if channel cant be decoded
#    03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
#    01 update only new keys, default setting
#    02 update all keys (used for valid PMK checking)
#    04 enable TPS au
#    + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
#    00 files in /var/keys
#    01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
#    00 no network (default)
#    01 newcamd netclient
#    02 radegast netclient
#    04 camd3 netclient
#    08 gbox netclient
#    32	cccamd netclient, card list saved as /tmp/cccamd.info 
#    	(ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
#    00 disable
#    01 retry every new ecm
#    02 try to connect to offline shares every Q: seconds
#    04 try to detect and fast reconnect to lost (and not used atm) server
#    + XX messages number and YY seconds to reconnect
#    mg will reconnect to server, if no answer to last XX ecm/keepalive or
#    if no answer for last ecm or keepalive sent for YY seconds
#    set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
#    00 No OSD (default)
#    01 neutrino
#    02 enigma
#    03 relook
#    + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
#    01 show emu ecm 
#    02 show network shares messages
#    04 show decoding failed / fta
#    08 show emm keys update
#    + web port to use for osd
S: { 03 } 80

# Log option, summ of:
#    00 off
#    01 network udp log
#    02 log to console
#    04 file, appended ! delete it by yourself, before it eat all your hdd
#    + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value, 
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
#    00 Off (default)
#    01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
#    02 Ecm data cache, remember CW for (E:) time 
#    04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of: 
#    00 No (default)
#    01 reread config file on channel change (including priority and ignore, but not replace/cache)
#    02 reread SoftCam.Key on channel change
#    04 reread SoftCam.Key if file changed
R: { 04 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

newcamd.list

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 34000 test1 test2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

oscam.conf

[global]
nice = -1
logfile = /dev/null
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1

[monitor]
port = 988
nocrypt = 
aulow = 120
hideclient_to = 0
monlevel = 1
appendchaninfo = 1

[newcamd]
Port = 34000@0B00:000000
key = 0102030405060708091011121314
allowed = 
keepalive = 1
mgclient = 1


[webif]
httpport = 8888
httpuser = 
httppwd = 
httprefresh = 5
httphideidleclients = 0
httpallowed = 0.0.0.0 - 255.255.255.255
debug = 255

oscam.server

[reader]
label = SatBG
protocol = internal
detect = cd
device = /dev/sci0
caid = 0B01
EMMCache = 1,1,0 
group = 1

oscam.user

[account]
user = test1
pwd = test2
monlevel = 0
group = 1
au = 1
caid = 0B01

[sjamesamuel]

Re: How mgcamd is installed in dm800se enigma2?

Did you set the permission for the file in /usr/bin?

[tech1010]

Re: How mgcamd is installed in dm800se enigma2?

Friends still not get solution.. ? I downloaded mgcamd with all ready files. How and where to set these all files of mgcamd.. Thanks

[gauloises1]

Re: How mgcamd is installed in dm800se enigma2?

A question in that direction:

Before I change my running system - what are the advantages of mgcamd compared with cccamd 2.21 as cs-client?

mgcamd is a little faster than cccam

[aplok]

Re: How mgcamd is installed in dm800se enigma2?

when installed,
to convert cccam config into mgcam config, do this:

cat /var/etc/CCcam.cfg >> /var/keys/cccamd.list

[tech1010]

Re: How mgcamd is installed in dm800se enigma2?

A question in that direction:

Before I change my running system - what are the advantages of mgcamd compared with cccamd 2.21 as cs-client?

i need mgcamd for dish tv. Dish tv is using multi encryption system.. Cccam works only to open conax channels other encryptions open with mgcamd,. Actually i have installed mgcamd so many times in softcams menus.. But mgcamd not working.. Even when i put my c line in mgcamd conx channels too stop working.. Mgcamd is not working.. Then i am trying to install mgcamd with dcc.